share this post
on this page
With the Dutch time-of-use grid tariffs that apply from 2028, large consumers pay their grid operator for how high their peak is and for when it happens. For a distribution centre that charges its e-trucks as soon as they’re back on site, that’s bad news. The trucks return between four and six in the afternoon. In winter, that’s exactly when the grid is at its busiest.
The Netherlands Authority for Consumers and Markets (ACM), the Dutch energy regulator, has set out the new tariff structure for every business with a connection above 3×80 amps on a regional grid. The intended start date is 1 January 2028. Businesses connected directly to TenneT’s high-voltage grid have paid this way since 2025. If you run a depot or hub in the Netherlands, this applies to you, whatever country your head office is in.
The timing of your highest quarter-hour will decide what you pay your grid operator. For logistics businesses that charge on return, that gets expensive.
- Every quarter-hour gets a weighting factor between 0.10 and 1.00, based on the month, the hour and whether it’s a working day.
- On working days from November to February, use between 16:00 and 22:00 weighs the most: factor 1.00.
- You pay each month on your highest weighted quarter-hour. One badly timed charging session sets the peak costs for that whole month.
- In our worked example, a depot with eight e-trucks cuts its weighted peak from 970 kW to 319 kW, just by moving charging to after midnight.
- Large consumers within one grid area pay the same in total as before. Those who can’t shift their load pay the difference.
When you charge now matters as much as how much you charge.
What changes in your grid tariff?
As a large consumer in the Netherlands, you pay your grid operator on three components: your contracted capacity, your highest measured quarter-hour each month (kWmax) and, on a medium or low-voltage connection, the kWh you take from the grid. In the old structure, it doesn’t matter when your peak happens. A peak at three in the morning costs the same as one at five in the afternoon.
Under the time-of-use tariffs, contracted capacity stays a fixed component. The other two start to move with how busy the grid is:
The weighting schedule is fixed in the Dutch Tariff Code and is the same across the whole country. It has three seasons (winter from November to February, summer from May to August, and the four months in between) and separates working days from weekends and public holidays. The rates in euros do differ per grid operator and are set again every year. The full schedule is in the draft decision by the ACM (in Dutch).

Generated with AI
Why charging on return gets so expensive in winter
On a winter working day, factor 1.00 applies from 08:00 to 10:00 and from 16:00 to 22:00. That second block is exactly when most trucks come back and go straight onto the charger. Every kW you draw then counts in full.
Two details make it harder than it looks. You pay on the monthly peak, so one afternoon when all trucks plug in at once sets the peak costs for the whole month. A quiet rest of the month won’t make up for it. And winter nights are less cheap than many people expect. Between midnight and 07:00, the factor is 0.58. The low factors of 0.10 and 0.25 don’t appear at all in the winter months.
There is an opening in the middle of the day. Between 12:00 and 15:00, the factor on winter working days drops to 0.58. For trucks that are back between two runs, that’s a useful charging window.
In summer, the problem moves. The midday window is then very cheap, with factor 0.10 between 13:00 and 15:00. The late evening, from 21:00 to midnight, weighs the most at 0.82. A charging schedule that works well in January can land in the wrong place in July.
Worked example: a depot with eight e-trucks
Take a fictional distribution centre with a base load of 250 kW during the day and 150 kW at night. It runs eight electric tractor units that each need 300 kWh after their run to leave fully charged at 06:00 the next morning. The chargers deliver 90 kW per truck.
Scenario 1: charging on return.
All trucks are on charge at 16:30 on a working day in January. The peak comes to 250 kW plus 8 x 90 kW, 970 kW in total. With factor 1.00, the weighted peak is also 970 kW. If your contracted capacity is lower, you also have a problem when you exceed your contracted capacity.
Scenario 2: charging after midnight.
The trucks charge from 00:00, spread over six hours. The 2,400 kWh then needs an average of 400 kW of charging power. Add 150 kW of base load and you reach 550 kW. With factor 0.58, the weighted peak is 319 kW. The daytime base load of 250 kW during the most expensive hours stays below that, so 319 kW is your monthly peak.
The same amount of energy gives a weighted peak about two thirds lower. The kWh also move from the most expensive rate to a cheaper one.
This only works if your route planning allows it. A truck that comes in at 16:30 and leaves again at 19:00 can’t wait until after midnight. In that case it helps to cap charging power during the most expensive hours, give that truck priority and charge the rest of the fleet later.

Who will pay more?
The ACM is open about this. Large consumers within the area of one grid operator pay the same in total as before. The new structure only splits the costs differently across that group. Because everyone’s weighted peaks add up to less than the unweighted peaks, the rate per weighted kW is higher than the old peak rate.
If you can shift your load, you gain. If you can’t, you pay more. In logistics, that mainly means cold storage and frozen-food distribution centres. Their load runs day and night, winter evenings included, and is hard to move.
For fleets that already charge at night, less changes. Their charging peak on winter nights already falls in the 0.58 block, and smarter charging adds little there. The biggest gains are for businesses that charge on return today.
What you can do now
The weighting schedule is public and fixed for the long term. So you can already see where your peaks fall and what you can do about them.
With eight trucks, changing routes and a schedule that shifts with the seasons, you can’t keep track of this by hand. An energy management system can plan charging sessions automatically: cap charging power when it’s expensive, spread the load over cheaper hours and make sure every truck is full on time. Read more about how that works in practice in our blog on smart charging for large fleets.
Time-of-use tariffs apply to every large consumer on a Dutch regional grid. For businesses with a lot of flexibility, there are also alternative transport rights, which give a discount in return for less firm grid capacity. And with a group transport agreement (GTO), several businesses on one site can sign a single transport agreement together.
The Netherlands is early here, but probably not alone for long. The European Commission has proposed that network tariffs across the EU should include time-dependent elements.
Do you know when your fleet sets its highest peak?
Tibo EMS controls chargers, batteries and solar panels based on live data, departure times and the limits you set. Its algorithm makes new decisions every five minutes. As a result, your trucks charge outside the expensive hours as much as possible, without any of them leaving late. In a demo, we show you how that works for a fleet like yours. Book a demo.
Frequently asked questions
follow us
Don't miss the next spark.
Subscribe and catch the latest in energy management.




